Double Bend Electrode

DOUBLE-BEND, WITH STANDARD NOSE DESIGNS

These standard cold-formed electrodes are bent from straight electrodes (some after added machining) and have the same hardness and conductivity. They outlast, many times over, the old cast and forged electrodes of similar geometry, which are impossible to cool adequately.

The table shows a wide range of electrodes generally available from stock. For sizes not shown, refer to the diagrams and description key at the bottom of the page, and order what you need. All measurements will be accurate. However, over-all length, in 1/8-in. multiples, will be held to within 1/16-in.

Tapers, water holes, and nose designs are the same as the standard straight electrodes in this catalog. Water tubes can be furnished.

Standard nose designs other than those shown here may be furnished on short order. Follow the "Key to Description", using a 'B' for Dome nose, 'C' for flat nose, 'E' for truncated cone, and 'F' for radius nose.

 

Special Order Information:

Special Order Information

Bent Electrodes 4RW Taper
Bent Electrodes 4RW Taper
LengthOffsetCLASS 1 A Pointed Nose DescriptionCLASS 1 A Pointed Nose Part NumCLASS 1 D Offset Nose DescriptionCLASS 1 D Offset Nose Part NumCLASS 2 A Pointed Nose DescriptionCLASS 2 A Pointed Nose Part NumCLASS 2 D Offset Nose DescriptionCLASS 2 D Offset Nose Part Num
1-1/16 1/2         FA-2317-8 167-0060    
2-3/16 1             FD-2423-16 167-2080
2-1/4 1/2 FA-1424-8 165-0100     FA-2424-8 167-0100    
2-1/4 3/4         FA-2424-12 167-0120    
2-3/8 3/8 FA-1426-6 165-0160     FA-2426-6 167-0160    
2-3/8 3/4         FA-2426-12 167-0180    
2-3/8 1-1/4 FA-1426-20 165-0200 FD-1426-20 165-2200 FA-2426-20 167-0200 FD-2426-20 167-2200
2-1/2 1/2         FA-2428-8 167-0240    
2-1/2 1 FA-1428-16 165-0280 FD-1428-16 165-2280 FA-2428-16 167-0280 FD-2428-16 167-2280
2-5/8 3/4 FA-14210-12 165-0320     FA-24210-12 167-0320 FD-24210-12 167-2320
2-3/4 1/2 FA-14212-8 165-0360     FA-24212-8 167-0360 FD-24212-8 167-2360
2-3/4 1         FA-24212-16 167-0400    
2-3/4 1-1/4         FA-24212-20 167-0420    
2-7/8 3/4         FA-24214-12 167-0430    
2-7/8 1-1/4 FA-14214-20 165-0460     FA-24214-20 167-0460    
3 1 FA-1430-16 165-0520     FA-2430-16 167-0520    
3-3/8 1-1/4         FA-2436-20 167-0580    
3-1/2 1         FA-2438-16 167-0620    
Bent Electrodes 5RW Taper
Bent Electrodes 5RW Taper
LengthOffsetCLASS 1 A Pointed Nose DescriptionCLASS 1 A Pointed Nose Part NumCLASS 1 D Offset Nose DescriptionCLASS 1 D Offset Nose Part NumCLASS 2 A Pointed Nose DescriptionCLASS 2 A Pointed Nose Part NumCLASS 2 D Offset Nose DescriptionCLASS 2 D Offset Nose Part Num
2-1/4 1/2             FD-2524-8 167-3100
2-1/4 1-1/4     FD-1524-20 165-3140     FD-2524-20 167-3140
2-3/8 3/8 FA-1526-6 165-1160     FA2526-6 167-1160 FD-2526-6 167-3160
2-3/8 3/4     FD-1526-12 165-3180 FA-2526-12 167-1180 FD-2526-12 167-3180
2-1/2 1/2 FA-1528-8 165-1240     FA-2528-8 167-1240    
2-1/2 1         FA-2528-16 167-1280    
2-3/4 1/2 FA-15212-8 165-1360 FD-15212-8 165-3360 FA-25212-8 167-1360 FD-25212-8 167-3360
2-3/4 3/4         FA-25212-12 167-1380    
2-3/4 1 FA-15212-16 165-1400 FD-15212-16 165-3400 FA-25212-16 167-1400 FD-25212-16 167-3400
2-7/8 1         FA-25214-16 167-1440    
2-7/8 1-1/4 FA-15214-20 165-1460     FA-25214-20 167-1460    
3 1/2 FA-1530-8 165-1480     FA-2530-8 167-1480 FD-2530-8 167-3480
3 3/4         FA-2530-12 167-1500    
3 1         FA-2530-28 167-1540 FD-2530-16 167-3520
3-1/4 1 FA-1534-16 165-1560     FA-2534-16 167-1560    
3-3/8 3/8     FD-1536-6 165-3570        
3-3/8 1-1/4 FA-1536-20 165-1580 FD-1536-20 165-3580 FA-2536-20 167-1580 FD-2536-20 167-3580
3-1/2 1/2 FA-1538-8 165-1600     FA-2538-8 167-1600    
3-1/2 1         FA-2538-16 167-1620 FD-2538-16 167-3620

Product Catalog © 2015 Tuffaloy Products Inc. All Rights Reserved.